Huawei ECC800-Pro Скачать руководство пользователя страница 307 | Manualshive

Страница: 307 / 368

background image

whether the parameter settings are consistent with the independent

deployment AI_DI unit parameters.

----End

8.1.7.27 How Can I Set and Add a UIM20A Expansion Module (Modbus-TCP)?

Prerequisites

Connect one end of a network cable to the PoE port on the UIM20A expansion

module and the other end to the LAN port on the ECC800-Pro or the PoE port on

the smart ETH gateway.

NO TE

Cascading of UIM20A expansion modules is not supported.

Context

The UIM20A expansion module supports self-discovery and does not need to set

parameters.

Procedure

Step 1 Set the running parameters and control parameters for the UIM20A expansion

module on the WebUI.
1. Log in to the ECC800-Pro WebUI as an administrator.
2. Choose Monitoring > System > UIM Group > UIMn.
3. On the Running Parameters tab page, set UIM20A expansion module

running parameters.

4. On the Controls tab page, set the UIM20A expansion module control

parameters.

----End

8.1.7.28 How Can I Set and Add a Multi-functional Sensor?

If a multi-functional sensor is installed, perform the following steps to configure it.

Prerequisites

One end of the straight-through cable has been connected to the PoE port on the

multi-functional sensor, and the other end has been connected to the PoE port on

the smart ETH converter.

Procedure

Step 1 Set multi-functional sensor parameters.

On the WebUI, choose Monitoring > Aisle > Multi-Func Sensor Group > Multi-

Func Sensor1 > Running Parameters, ensure that Smoke enable and Temp

enable are set to Enable, set High temperature alarm threshold and other

parameters as required, and then click Submit.

ECC800 Data Center Controller

User Manual (for ECC800-Pro)

8 FAQ

Issue 02 (2020-09-07)

Copyright © Huawei Technologies Co., Ltd.

296

«
...
305
306
307
308
309
...
»

Содержание ECC800-Pro

















































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ECC800-Pro

Бренд: ABB Страницы: 139

Бренд: ABB Страницы: 28

Бренд: ABB Страницы: 59

Бренд: Jafar Страницы: 9

Бренд: Microchip Technology Страницы: 37

Бренд: Lawler Страницы: 4

Бренд: Hama Страницы: 46

Бренд: Galcon Страницы: 35

Бренд: Eaton Страницы: 288

Бренд: K'Nex Education Страницы: 56

Бренд: RadioMaster Страницы: 10

Бренд: Xblue Networks Страницы: 2

Extinguishing Control Panel BC06-2EXT

Бренд: LST Страницы: 4

CentralControl CC41

Бренд: Becker Страницы: 48

Бренд: GSK Страницы: 32

Бренд: Mitsubishi Страницы: 30

eTracer ET4415BND

Бренд: Epsolar Страницы: 44

Бренд: Graco Страницы: 166

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды