Huawei ECC800-Pro Скачать руководство пользователя страница 305 | Manualshive

Страница: 305 / 368

background image

Step 6 On the IP Device 1-5 tab page, set Enable online detection IP device 1 to

Enable.

Step 7 Click Submit.

Step 8 Specify IP device 1 address.

NO TE

● Set IP device 1 address to the IP address of IP device 1. For example, set IP device 1

address to 192.168.2.137.

● Add other IP devices in the same way.

Step 9 Click Submit.

Step 10 (Optional) If you need to change the name of an IP device, perform the following

steps:
1. Choose System Settings > Signal Name Modify. The Batch Signal

Configuration page is displayed.

2. Set Device type to ECC800, set Device name to ECC800, and click OK.
3. On the query result tab page, set the new signal name of IP device 1 to XXX

and click Submit.

----End

8.1.7.26 How Can I Set and Add an Independent Deployment AI_DI Unit?

Prerequisites

One end of the straight-through cable has been connected to the COM_IN port on

the independent deployment AI_DI unit, and the other end has been connected to

the COM port on the ECC800-Pro collector or ETH converter.

Procedure

Step 1 Set monitoring parameters for the independent deployment AI_DI unit.

Set the address of the independent deployment AI_DI unit to 1 or 2 by setting its

DIP switch.

The DIP switch consists of toggle switches 1–4 (from left to right). Toggle switches

1–3 specify the address of the independent deployment AI_DI unit. Toggle switch 4

specifies the address of the RS485 build-out resistor. 1 indicates ON, and 0

indicates OFF.

NO TE

The device address for the independent deployment AI_DI unit can only be set to 1 or 2.

Table 8-22 Setting a device address

Address

Toggle Switch 1

Toggle Switch 2

Toggle Switch 3

1

OFF

ON

ON

ECC800 Data Center Controller

User Manual (for ECC800-Pro)

8 FAQ

Issue 02 (2020-09-07)

Copyright © Huawei Technologies Co., Ltd.

294

«
...
303
304
305
306
307
...
»

Содержание ECC800-Pro

















































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ECC800-Pro

Бренд: jbc Страницы: 4

Бренд: Samson Страницы: 92

Бренд: Jafar Страницы: 10

EtherNetIP ControlPlex CPC12EN

Бренд: E-T-A Страницы: 28

Бренд: Harmonic Drive Страницы: 25

Бренд: Nelson Страницы: 8

Бренд: Harpo Страницы: 35

Бренд: Hardi Страницы: 2

Бренд: U.S. Divers Страницы: 22

Бренд: Watlow Страницы: 59

Tekmar WiFi Snow Melting Control 670

Бренд: Watts Страницы: 48

Бренд: Universal Remote Страницы: 20

Бренд: Watts Страницы: 17

Travel About Series

Бренд: Kolcraft Страницы: 14

Бренд: Miller-Leaman Страницы: 18

Бренд: XtendLan Страницы: 12

Бренд: ZBA Страницы: 27

Бренд: M-system Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды