Huawei ECC800-Pro Скачать руководство пользователя страница 282

Страница: 282 / 368

Path

Parameter

Setting

and click Add

Device. The

parameters

for adding

devices are

displayed.

Connect To

Select ECC800 from the drop-down list

box.

Communicati

ons Port

Select COM2 from the drop-down list box.

Device

Address

In this example, Device Address is set to 1.

During actual configuration, set the device

address for the SVG based on the actual

situation.

3. Click Test Connect to check whether the SVG connects to the ECC800-Pro

properly.
–

If the connection succeeds, click Confirm. The connected devices are

displayed in the Number of connected devices list.

–

If the connection fails, check whether the device is properly connected to

the ECC800-Pro, whether the device and ECC800-Pro are running

properly, and whether the parameter settings are consistent with the

device parameters.

----End

8.1.7.9 How Can I Set and Add an Envicool Air Conditioner (Modbus-RTU)?

Prerequisites

One end of the straight-through cable has been connected to terminals 1 and 2

on the air conditioner electric control box, and the other end has been connected

to the COM/AIDI port on the ECC800-Pro collector or UIM20A.

(Optional) One end of the straight-through cable has been connected to terminals

7 and 8 on the air conditioner electric control box, and the other end has been

connected to the COM/AIDI port on the ECC800-Pro collector or UIM20A.

NO TE

● Terminals 1 and 2 of the air conditioner electric control box are RS485+ and RS485–,

respectively. Terminals 7 and 8 are Boolean dry contacts, which are polarity insensitive.

● Cables need to be connected to both the Envicool CRU and IFX end devices.

Procedure

Step 1 Set monitoring parameters for the air conditioner.

1. On the home screen of the air conditioner, click SetPoint, enter the password

8866, and click OK.

2. On the air conditioner parameter setting page, set MonAddr to 1.

Step 2 Add an Envicool air conditioner (Modbus-RTU).

1. Log in to the ECC800-Pro WebUI as an administrator.

ECC800 Data Center Controller

User Manual (for ECC800-Pro)

8 FAQ

Issue 02 (2020-09-07)

271

Содержание ECC800-Pro

















































































































































































































































































































































































Результаты поиска

Содержание ECC800-Pro

Отзывы:

Похожие инструкции для ECC800-Pro

Бренды по названию

Популярные бренды

Huawei ECC800-Pro, Руководство пользователя

Результаты поиска

Содержание ECC800-Pro

Отзывы:

Похожие инструкции для ECC800-Pro

Бренды по названию

Популярные бренды