Huawei ECC800-Pro Скачать руководство пользователя страница 262

Страница: 262 / 368

Step 8 Connect the communications cables and antennas to the ECC800-Pro main control

module.

Step 9 Choose Maintenance > Configuration File and import the backup configuration

file, or set parameters for the devices that connect to the ECC800-Pro to ensure

normal communication.

----End

7.3.2 Replacing an ECC800-Pro PSU

Prerequisites

D ANGER

Do not touch the terminals in the rear of a removed PSU to avoid electric shocks.

●

Tool: insulation gloves

●

Materials: a reserved undamaged and undeformed PSU of the appropriate

model.

Context

The PSU is hot-swappable.

Procedure

Step 1 Push the locking latch in the upper right corner of the PSU panel leftwards.

Step 2 Pull out the handle of the PSU to remove the PSU from the subrack.

Step 3 Gently push the reserved PSU into the subrack along guide rails, and push the

locking latch rightwards to secure the handle.

Figure 7-3 Replacing a PSU

----End

ECC800 Data Center Controller

User Manual (for ECC800-Pro)

7 Maintenance

Issue 02 (2020-09-07)

251

Содержание ECC800-Pro

















































































































































































































































































































































































Результаты поиска

Содержание ECC800-Pro

Отзывы:

Похожие инструкции для ECC800-Pro

Бренды по названию

Популярные бренды

Huawei ECC800-Pro, Руководство пользователя

Результаты поиска

Содержание ECC800-Pro

Отзывы:

Похожие инструкции для ECC800-Pro

Бренды по названию

Популярные бренды