Huawei ECC800-Pro Скачать руководство пользователя страница 260 | Manualshive

Страница: 260 / 368

background image

Symptom

Possible Cause

Measure

The RUN indicator is

blinking at short

intervals (on for 0.125s

and then off for 0.125s).

Communication between

the independent

deployment AI_DI unit

and the main control

module is interrupted.

Check whether the cable

connection between the

ECC800-Pro and

independent deployment

AI_DI unit is normal,

whether the independent

deployment AI_DI unit is

faulty, and whether the

independent deployment

AI_DI unit is added on

the ECC800-Pro WebUI.

The ALM indicator is on.

An alarm whose default

severity is major exists.

Check and clear the

alarm.

7.3 Component Replacement

1. After replacing components, log in to the WebUI and choose Maintenance >

Parameter Sync to access the parameter synchronization page.

2. Click Device type and select the component type from the drop-down list.
3. Select the failure device in Source Device, select the reserved device in Target

Device, and click Submit to synchronize the configuration parameters of the

failure device to the reserved device.

4. On the Monitoring > System > ECC800 > Controls tab page, select Delete

device with communication failure and click Submit, add the reserved

device to the smart module view.

7.3.1 Replacing an ECC800-Pro Main Control Module

Prerequisites

NO TICE

● The ECC800-Pro main control module is hot-swappable.
● Before disconnecting cables from the ECC800-Pro main control module, label

the cables based on the corresponding ports.

●

Tools: ESD wrist strap, ESD gloves, Phillips screwdriver, labels, marker

●

Materials: a new undamaged and undeformed ECC800-Pro main control

module of the appropriate model

Procedure

Step 1 Use the Back Up Current Settings function to record the ECC800-Pro

configuration information or manually record the information.

ECC800 Data Center Controller

User Manual (for ECC800-Pro)

7 Maintenance

Issue 02 (2020-09-07)

Copyright © Huawei Technologies Co., Ltd.

249

«
...
258
259
260
261
262
...
»

Содержание ECC800-Pro

















































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ECC800-Pro

Бренд: Caen Страницы: 20

Бренд: B&G Страницы: 19

GECO LUX GECO60

Бренд: GiBiDi Страницы: 48

Бренд: Reer Страницы: 2

Бренд: Fibocom Страницы: 79

Бренд: oventrop Страницы: 40

Бренд: REGLOPLAS Страницы: 44

Бренд: Sentiotec Страницы: 45

Бренд: Gecko Страницы: 82

Бренд: SAGEMCOM Страницы: 2

Бренд: Instant Care Страницы: 2

Soluna Remote Control

Бренд: Rollei Страницы: 8

Бренд: TSM Страницы: 2

WFHC 06Z 02 HC RF 24

Бренд: Watts Страницы: 18

Бренд: Waters Страницы: 39

DHI-IPMECD-3021 Series

Бренд: Dahua Technology Страницы: 28

Errata MSP430F6779

Бренд: Texas Instruments Страницы: 27

Бренд: MELICONI Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды