manualshive.com logo in svg

Huawei E8000E-X16, Руководство пользователя

Поделиться
Скачать
Huawei E8000E-X16 Скачать руководство пользователя страница 152

Table A-3

 Buttons and indicators on the panel of the MPUB

Indicator/Button

Description

OFL button

To remove a board, you must hold the button for six seconds until
the OFL indicator turns on.
This button takes effect only on the slave MPUB.

OFL indicator (red)

If the indicator is on, it indicates that you can remove the board.

RUN indicator (green)

If the indicator blinks once every two seconds (0.5 Hz), it
indicates that the system is in the normal state.
If the indicator blinks twice each second (2 Hz), it indicates that
the system is in the alarm state.

ALM indicator (red)

If the indicator is steady on, it indicates that the system is in the
alarm state.
If the indicator is steady off, it indicates that the system is in the
normal state.

ACT active/standby
indicator (green)

If the indicator is steady on, it indicates that the MPUB is in the
active state.
If the indicator is off, it indicates that the MPUB is in the standby
state.

Reset button

The button is used for resetting the MPUB. If you press the Reset
button, you can reset the MPUB.

CF ACT indicator (green) If the indicator is on, it indicates that the CF is in position.

If the indicator is blinking, it indicates that data is being read or
written.
If the indicator is off, it indicates that the CF is not in position or
can be removed.

CF OFL button

If you press the CF OFL button, all operations on the CF card
will be ended and the CF card will be powered off.

SFP LINK/ACT indicator
(green)

If the indicator is steady on, it indicates that the link is normal.
If the indicator is blinking, it indicates that data is being
transmitted.

MGMT-ETH LINK
indicator (green) (on
Ethernet network
interfaces)

If the indicator is steady on, it indicates that the link is normal.
If the indicator is off, it indicates that the link is down.

MGMT-ETH ACT
indicator (amber) (on
Ethernet interfaces)

If the indicator is blinking, it indicates that data is being
transmitted.
If the indicator is off, it indicates that no data is being transmitted.

 

A.1.4 SFU Indicators

HUAWEI Eudemon8000E Firewall
Hardware Description

A List of Indicators

Issue 01 (2012-11-07)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

142

Содержание E8000E-X16























































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды