manualshive.com logo in svg

Huawei CX320, Руководство пользователя

Поделиться
Скачать
Huawei CX320 Скачать руководство пользователя страница 96

login as:

Step 7

Enter the user name and password.

If the log in is successful, the host name is displayed on the left of the prompt.

----End

6.4 Powering On or Off a Switching Plane

This topic describes how to power on or off the converged switching plane of CX320.

Scenarios

Use any of the following methods to power on the CX320:

l

Power on all switching planes of the CX320 on the MM910 WebUI. Details are provided
later in this topic.

l

On the MM910 CLI, run the 

powerstate

 command to power on or off the switching

planes of the CX320. For details, see 

MM910 Management Module V100R001

Command Reference

.

l

On the BMC CLI, run the 

powerstate

 command to power on or off the switching planes

of the CX320. For operation details, see 

E9000 Server V100R001 iBMC User Guide

.

l

If the chassis is not powered on, power it on, and all the switching planes of the CX320
will be powered on with the chassis. This topic does not provide the operation details.

l

If the chassis is powered off, the converged switching plane of the CX320 is powered off
with the chassis.

l

If the chassis is powered on but the CX320 is not installed, install the CX320, and all
switching planes of the CX320 are automatically powered on after installation. This
topic does not provide the operation details.

l

If the chassis is powered on and the CX320 is installed, remove the CX320 to power off
the converged switching plane.

Impact on the System

After the converged switching plane is powered off, all services that run on the converged
switching plane stop.

Prerequisites

Software

PuTTY.exe is free software. You can download it from the Internet. PuTTY 0.60 or later is
required for login over a serial port.

Procedure

Step 1

Connect The RS–232 serial port on the PC to the serial port marked with 

COM

 on the CX320

panel.

Step 2

Save the current configuration data.

CX320 Switch Module
User Guide

6 Common Operations

Issue 09 (2019-08-02)

Copyright © Huawei Technologies Co., Ltd.

90

Содержание CX320


















































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды