Huawei CX320 Скачать руководство пользователя страница 91

Страница: 91 / 113

NOTE

Only one serial port connection can be set up at a time. Exit the SOL interface after the operation.

You can press

Ctrl+R

to return to the CLI for selecting a slot in the chassis, as shown in

Step 3

. And

you can press

ctrl+r

twice to log out of the SOL CLI.

----End

6.2 Logging In to the MM910 CLI Over a Network Port by
Using PuTTY

This topic describes how to use PuTTY to remotely log in to a server over a local area
network (LAN) and to configure and maintain the server.

NOTE

The compute nodes and switch modules of the E9000 do not provide the MGMT management port.

To log in to a compute node or switch module, see

6.1 Logging In to or a Switch Module over

MM910 SOL

Prerequisites

Data

IP address of the MM910 to be connected

User name and password for logging in to the MM910

Software

PuTTY.exe

: third-party software used for remote access on various platforms.

Procedure

Step 1

Connect the local PC and the MGMT port on the MM910 through a network cable.

Step 2

Set an IP address and a subnet mask or add route information for the PC to enable
communication between the PC and the MM910.

To check the connectivity between the PC and the device, run the

Ping MM910 IP address

command on the PC CLI.

Step 3

Double-click

PuTTY.exe

The

PuTTY Configuration

window is displayed.

Step 4

In the navigation tree on the left, choose

Connection

SSH

Step 5

Set the login parameters as follows:

Host Name (or IP address)

: Enter the IP address of the MM910 to be logged in to, for

example,

191.100.34.32

Port

: Use the default value

Connection type

: Use the default value

SSH

Close window on exit

: Use the default value

Only on clean exit

CX320 Switch Module
User Guide

6 Common Operations

Issue 09 (2019-08-02)

Содержание CX320


















































































































Результаты поиска

Содержание CX320

Отзывы:

Бренды по названию

Популярные бренды

Huawei CX320, Руководство пользователя

Результаты поиска

Содержание CX320

Отзывы:

Бренды по названию

Популярные бренды