manualshive.com logo in svg

Huawei CX320, Руководство пользователя

Поделиться
Скачать
Huawei CX320 Скачать руководство пользователя страница 110

--------------------------------------------------------------------------------  
   

3.

Obtain the log file.

<HUAWEI>

ftp 192.168.100.122

Trying 192.168.100.122 ...                                                       
Press CTRL+K to abort                                                            
Connected to 192.168.100.122.                                                    
220 WFTPD 2.0 service (by Texas Imperial Software) ready for new user            
User(192.168.100.122:(none)):

huawei

                                             

331 Give me your password, please                                                
Enter password:                                                                  
230 Logged in successfully     

[ftp]

binary

200 Type is Image (Binary)

# On the FTP server, create a log receiving directory for the master switch module in the
stack. Replace 

3

 in 

swi3

 with the actual stack ID of the master switch module. The stack ID is

the switch module slot ID. (If the switch modules are not stacked, create a log receiving
directory for the current switch module by replacing 

3

 in 

swi3

 with the slot ID of the current

switch module.)

[ftp]

mkdir swi3

[ftp]

cd swi3

[ftp]

put flash:/diag-info.txt

200 Port command successful. 
150 Opening data connection for diag-info.txt. 
/     100% [***********]  
226 File received ok 
 
FTP: 1756870 byte(s) send in 0.308 second(s) 5570.431Kbyte(s)/sec.

[ftp]

mput flash:/logfile/*

200 Port command successful. 
150 Opening data connection for diag.log. 
/     100% [***********]  
226 File received ok 
 
FTP: 7971326 byte(s) send in 0.798 second(s) 9755.010Kbyte(s)/sec. 
200 Port command successful. 
150 Opening data connection for diaglog_3_20140221182310.log.zip. 
/     100% [***********]  
226 File received ok 
 
FTP: 444920 byte(s) send in 0.113 second(s) 3845.061Kbyte(s)/sec. 
200 Port command successful. 
150 Opening data connection for diagnostic_information.zip. 
/     100% [***********]  
226 File received ok 
 
FTP: 1756870 byte(s) send in 0.308 second(s) 5570.431Kbyte(s)/sec. 
200 Port command successful. 
150 Opening data connection for log.log. 
/     100% [***********]  
226 File received ok 
 
FTP: 4272491 byte(s) send in 3.492 second(s) 1194.832Kbyte(s)/sec. 
200 Port command successful. 
150 Opening data connection for log_3_20131222113233.log.zip. 
/     100% [***********]  

CX320 Switch Module
User Guide

6 Common Operations

Issue 09 (2019-08-02)

Copyright © Huawei Technologies Co., Ltd.

104

Содержание CX320


















































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды