Huawei BTS3900 V100R003 Скачать руководство пользователя

Страница: 116 / 264

Figure 4-15

FAN panel

Figure 4-16

FANc panel

NOTE

The FANc has

FANc

label, which is different from the FAN.

Functions

The FAN unit performs the following functions:

Controls the fan speed.

Reports the status, temperature, and in-position signal of the fans to the main control
processing unit.

Monitors the temperature at the air inlet.

Dissipates heat.

The FANc supports the function of reading and writing the information reported by the
electronic label unit.

LED

The FAN panel has only one LED, which indicates the operating status of the fans.

Table

4-26

describes the LED.

4 BTS3900 Components

BTS3900

Hardware Description

4-24

Huawei Proprietary and Confidential

Issue 04 (2011-02-15)

Содержание BTS3900 V100R003









































































































































































































































































Результаты поиска

Содержание BTS3900 V100R003

Отзывы:

Похожие инструкции для BTS3900 V100R003

Бренды по названию

Популярные бренды

Huawei BTS3900 V100R003, Описание аппаратуры

Результаты поиска

Содержание BTS3900 V100R003

Отзывы:

Похожие инструкции для BTS3900 V100R003

Бренды по названию

Популярные бренды