Huawei BTS3900 V100R003 Скачать руководство пользователя

Страница: 101 / 264

NOTE

Bits 3 and 4 of

should be kept as out-of-factory state, without any manual setting on site. The out-of-

factory state should be OFF. If the bits are ON, set them to OFF.

Table 4-5

Details of the DIP Switch

DIP
Switch

Bit Status

Description

OFF

By default, all the DIP
bits of S2 are set to OFF
in all the modes.

When the four E1 RX
links in 75 ohm have
errors, all the bits of S2
must be set to ON to
rectify the faults on the
E1 links.

Others

Unavailable

Table 4-6

Details of the DIP Switch

DIP
Switch

Bit Status

Description

Supporting E1 bypass

OFF

Not supporting E1
bypass

Others

Unavailable

Table 4-7

Details of the DIP Switch

DIP
Switch

Bit Status

Description

Not supporting E1
bypass

OFF

Supporting E1 bypass
of level-1 cascaded
base stations

OFF

Supporting E1 bypass
of level-2 cascaded
base stations

BTS3900
Hardware Description

4 BTS3900 Components

Issue 04 (2011-02-15)

Huawei Proprietary and Confidential

4-9

Содержание BTS3900 V100R003









































































































































































































































































Результаты поиска

Содержание BTS3900 V100R003

Отзывы:

Похожие инструкции для BTS3900 V100R003

Бренды по названию

Популярные бренды

Huawei BTS3900 V100R003, Описание аппаратуры

Результаты поиска

Содержание BTS3900 V100R003

Отзывы:

Похожие инструкции для BTS3900 V100R003

Бренды по названию

Популярные бренды