manualshive.com logo in svg

Huawei 9000 VCT V100R011, Руководство администратора, Страница: 60 / 204

Поделиться
Скачать
Huawei 9000 VCT V100R011 Скачать руководство пользователя страница 60

Parameter

Description

Input source

This specifies the input source format.

NOTE

The ViewPoint 9039, ViewPoint 9036, ViewPoint 9035, ViewPoint 9033,
ViewPoint 9030, and HUAWEI VP9035A support video input with a resolution
of up to 1080p 30 Hz.

Mirroring

This specifies whether the terminal displays a reflection of an input
video, wherein the right and left sides of the original are reversed. By
default, 

Normal

 is selected. If the terminal is used in a Huawei

telepresence system, select 

Horizontal mirroring

.

l

Normal

: The input video will not be reversed.

l

Horizontal mirroring

: The terminal displays a reflection of the

input video, wherein the right and left sides of the original are
reversed like the reflection of something seen in a mirror.

1080p PsF
conversion

When the camera connected to the terminal uses the Progressive
segmented Frame (PsF) mode for transmitting signals, enable this
function.

Stretch mode

The terminal adjusts the input video based on the encoding format of
the video.

l

Stretch

: Stretch the video to the full-screen mode without locking

the aspect ratio of the video.

l

No stretch

: Stretch the video to the full-screen mode after locking

the aspect ratio of the video. Black borders may appear at the four
sides of the video display.

l

Intelligent stretch

: The system cuts the video to a proper size, and

then stretches the video to the full-screen mode after locking the
aspect ratio. For example, to change a wide-screen video to a narrow-
screen video, the system cuts the left and right sections of the wide-
screen video, and then stretches the video to the full-screen mode.

 

Table 3-6

 Common settings parameters

Parameter

Description

Remote control

This specifies whether a remote site can control the local camera during
a call. By default, 

Allow

 is selected.

Serial port type

This specifies the type of the serial port of the camera that is connected
to the terminal. You can select between RS232 and RS422.
The COM1 and COM2 serial ports on the rear panel of the terminal are
dual-mode ports that can be used as both RS232 and RS422 interfaces.

HUAWEI 9000 HD Video Terminal
Administrator Guide

3 Camera and Display

Issue 09 (2012-09-03)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

48

Содержание 9000 VCT V100R011













































































































































































































Отзывы:

Нет отзывов