manualshive.com logo in svg

Huawei 9000 VCT V100R011, Руководство администратора, Страница: 165 / 204

Поделиться
Скачать
Huawei 9000 VCT V100R011 Скачать руководство пользователя страница 165

Table 11-2

 Methods for upgrading the terminal software

Method

Usage

Upgrading the
software locally

After obtaining the upgrade software, connect a computer to the
terminal directly or over the local area network, and then upgrade
the terminal.

Upgrading the
software using the
minimum system

Set the terminal to the upgrade state forcibly. Connect a computer
to the terminal directly or using a switch, turn the switch on the rear
panel of the terminal to 

Load

, and then upgrade the terminal.

NOTE

l

If the hardware of the terminal works properly, the software can always
be upgraded successfully.

l

If upgrading the software locally fails, you can use this method.

Upgrading the
software from the web
interface

After obtaining the upgrade software, connect a computer to the
terminal directly or through the local area network, log in to the
terminal web interface, and upgrade the terminal.

 

Before the upgrade, note the following:

l

Read the 

Release Notes

 to understand the contents to be upgraded and precautions required

to be taken during the upgrade.

l

Check whether the current software version is earlier than the destination version.

l

Back up the settings on the terminal, such as the communication settings and the address
book.

11.2.1 Upgrading Software Locally Using a Computer

You can use a computer to upgrade the software of the terminal locally.

Before upgrading, note the following prerequisites:

l

A copy of the destination software is available on the computer.

l

The computer is connected to the terminal using a straight through network cable, crossover
network cable, or switch.

Upgrading a Single Terminal

You can upgrade a single terminal using the upgrade program installed on the computer.

Procedure

Step 1

Power on the computer and the terminal.

Step 2

Extract the compressed file of the upgrade software on the computer.

Step 3

Run 

UpgradeTool.exe

 to display the window as shown in 

Figure 11-1

.

HUAWEI 9000 HD Video Terminal
Administrator Guide

11 Maintenance and Troubleshooting

Issue 09 (2012-09-03)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

153

Содержание 9000 VCT V100R011













































































































































































































Отзывы:

Нет отзывов