manualshive.com logo in svg

Huawei 9000 VCT V100R011, Руководство администратора, Страница: 131 / 204

Поделиться
Скачать
Huawei 9000 VCT V100R011 Скачать руководство пользователя страница 131

Context

Pictures output or input from the Digital Visual Interface (DVI), SXGA interface, or YPrPb
interface (of the DVI-1 type), such as the computer desktop with the resolution of VGA when
displayed on the monitor screen, may deviate from their normal positions. In this case, set the
picture offset to adjust the picture position.

Procedure

Step 1

Choose 

Settings

 > 

Display

 > 

Image Offset

.

Step 2

Select a video interface, and then set the picture offset by moving the slider.

----End

7.1.3 Adjusting the Sampling Phase

When color distortion occurs in a picture on the monitor, adjust the sampling phase.

Context

Color distortion may occur on the input video, such as the computer desktop with the resolution
of VGA, when displayed on the monitor. That is, the color seen from the computer display is
different from the color seen from the monitor connected by the terminal. In this case, adjust the
color by setting the sampling phase.

Procedure

Step 1

Choose 

Settings

 > 

Display

 > 

Sampling Phase

.

Step 2

Set the sampling phase by moving the slider.

----End

7.1.4 Adjusting Video Parameters

After a Huawei HD camera is connected to the terminal, set the camera parameters, such as the
exposure mode, white balance mode, aperture size, and noise reduction, to view quality video
captured by the camera on monitors.

Prerequisites

Set the camera type of the video input source to a Huawei HD camera.

Context

If the VPC520 is connected to a video input interface, all the parameters listed in 

Table 7-2

 are

available to be set. If the VPC500 is connected to a video input interface, only certain parameters
listed in 

Table 7-2

 are available to be set. Refer to the relevant page for the specific parameters.

To check the camera connected to the video input interface, choose 

Settings

 > 

Video

 > 

Video

Input

.

HUAWEI 9000 HD Video Terminal
Administrator Guide

7 Video and Audio

Issue 09 (2012-09-03)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

119

Содержание 9000 VCT V100R011













































































































































































































Отзывы:

Нет отзывов