Huawei 3900 Series Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 196

background image

Figure 3-2

Procedure for commissioning the base station that starts to provide services of one

mode

1.

Configure the transmission data of the MBTS in mode A. The transmission data includes
but is not limited to E1, MP link, MP group, IP address, routing information, DHCP (used
at the MBTS in mode B) relay information, and VLAN.

(1) Configure the transmission data and export the data configuration file using the CME.

For details, see the

GBTS Initial Configuration Guide

,

NodeB Initial Configuration

Guide

, or

eNodeB Initial Configuration Guide

accordingly.

(2) Load the data configuration file to the base station in mode A. You are advised to load

the data configuration file locally using a USB disk. For details, see

6.3 Upgrading

Software and Configuring Data by Using the USB Disk

NOTE

You can configure other data of the base station in mode A after it is planned. The data configuration
of boards such as PMU and FUN in mode A must comply with mode B. Otherwise, alarm are reported
because of configuration conflict.

2.

Commission the MBTS in mode B by following the procedure for commissioning a single-
mode base station. For details, see the

GBTS Commissioning Guide

,

NodeB Commissioning

Guide

, or

eNodeB Commissioning Guide

accordingly.

3900 Series Multi-Mode Base Station
Commissioning Guide

3 Procedure for Commissioning the Base Station that Starts

to Provide Services of One Mode

Issue 02 (2010-07-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

3-3

«
...
23
24
25
26
27
...
»

Содержание 3900 Series





































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 3900 Series

Бренд: Valcom Страницы: 1

Бренд: Valcom Страницы: 13

Бренд: Valcom Страницы: 3

Бренд: Valcom Страницы: 4

Document WorkCentre 450c

Бренд: Xerox Страницы: 2

Бренд: Xerox Страницы: 4

Бренд: HBM Страницы: 40

Бренд: Varec Страницы: 70

ANDROID INTERFACE

Бренд: GMC Страницы: 18

Бренд: Prorack Страницы: 15

HookUpz Smartphone Telescope Adapter

Бренд: Carson Страницы: 16

Бренд: HHD Страницы: 5

Evolion 2.1 kWh

Бренд: Saft Страницы: 4

H-BLACK PRO DYNAMO

Бренд: HERRMANS Страницы: 2

Бренд: Modern Portable Страницы: 6

Бренд: Schwinn Страницы: 12

Бренд: E&G Classics Страницы: 3

Бренд: Grandstream Networks Страницы: 22

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды