HSD SM 137 D Скачать руководство пользователя страница 42 | Manualshive

Страница: 42 / 72

HSD SM 137 D Скачать руководство пользователя страница 42

5 Installation and commissioning

42

HSD S.p.A. © - h0104k01a.fm291119

Transmission speed setting (bit-rate)

The servo-motor is supplied with an initial bit-rate value of 500 Kbit/s.
If the value is not aligned with the one on the numerical control, it is necessary to follow the bit-rate
value setting procedure described below.

To set the required bit-rate value (DSW2), it is necessary to start the servo-motor with switch 6 On,
switch 5 Off and switches 1 to 4 set according to the bit-rate value required, as shown in the table
below.

Immediately after switch-on, the green servo-motor LED lights up for about 1 second. After this, if
the required bit-rate value has been successfully saved to the flash memory, it will start to flash
periodically with a number of blinks based on the bit-rate that has been selected.
If the dip-switch configuration is not one of those envisaged, the bit-rate value will remain as
before. If there are flash storage problems, the green LED will begin a 4-second flashing sequence
(2 seconds ON and 2 seconds OFF).
At the end of the procedure the servo-motor must be turned off and the dip-switch configuration
restored.

Dip-switch (DSW2)

Bit-rate

value

Flash*

to confirm

(green led DL3)

*

The LED flashes a certain number of times, followed by a pause before the "N" flashes are repeated.

6

5

4

3

2

1

On

Off

Off

Off

Off

On

1 Mbit/s

1

On

Off

Off

Off

On

Off

800 Kbit/s

2

On

Off

Off

Off

On

On

500 Kbit/s

3

On

Off

Off

On

Off

Off

250 Kbit/s

4

On

Off

Off

On

Off

On

125 Kbit/s

5

«
...
40
41
42
43
44
...
»

Содержание SM 137 D









































































Отзывы:

Нет отзывов