background image

06

(Throttle range should be reset whenever a new transmitter is being used) 

 Step 1:Switch on the transmitter and move the throttle stick to 100% 

(wide-open throttle).

Step 2:Connect the battery pack to the ESC, and wait about 2 seconds.

 Step 3:A 'beep-beep' tone will emit, this means the highest point in the 

throttle control range has been confirmed.

Step 4:After the 'beep-beep' tone is emitted, move the throttle stick 
back down to the lowest position (0%). You will hear a set of 
initialization beeps that register the number of cells in the battery.

Step 5:A final, long beep tone will be emitted meaning that the lowest 
point of the throttle range has been confirmed. This means the throttle 
control has been initialized properly and is ready for use.

Control Surface Centering

centered

.

If the control surfaces are not centered, mechanically center the 

control surfaces by adjusting the linkages

.

Clevis Installation

After assembly and transmitter setup,verify that the control surfaces are

1.

2.

3.

4.

5.

6.

With the flaps switch in the up position,flaps should be adjusted so they are 
even with the ailerons and

/

or the root of the wing

.

If adjustments are required, turn the ball buckle on the pushrod to 

change the length of the linkage between the servo arm and the 
control horn. After binding a transmitter to the aircraft receiver, set

 the trims and sub-trims to 0, then adjust the ball buckles as necessary 

to center the control surfaces.

* Adjust the pushrod and clevis as necessary.

*Carefully adjust the clevis so that it creates a centered surface 
  when attached to the control horn.

Throttle range setting

Содержание A1















Отзывы: