HS-Technik RoboRiv страница 57 Скачать руководство пользователя

Страница: 57 / 64

- 57 -

9 Troubleshooting and Fault repair

The RoboRiv by HS-Technik is a very stable and long-lasting tool.

If, however, a tool does not work properly you can find, and eliminate, the most frequent

causes for errors in the table below.

Error

Possible cause

Remedy

Tool does not start,

acoustic signal, red

Light field appears

1. Battery empty

2. Defective battery

1. Replace and charge battery

2. Replace battery

If the error still persists or is not listed, please contact HS-Technik GmbH.

Repairs:

Telephone:

+49 (0)7628 / 91 11-0

E-mail:

[email protected]

Programming:

Telephone:

+49 (0)7628 / 91 11-0

E-mail:

[email protected]

Please note the following information:

• Serial number of the riveting device (see battery compartment of the device)

• What error has occurred?

• Display

• When did the error first appear?

• What have you done to fix the error?

We reserve the right to make errors, technical changes to our products and changes to the

delivery programme in the course of further development.

Содержание RoboRiv

































































Результаты поиска

Содержание RoboRiv

Отзывы:

Похожие инструкции для RoboRiv

Бренды по названию

Популярные бренды

HS-Technik RoboRiv, Руководство по эксплуатации

Результаты поиска

Содержание RoboRiv

Отзывы:

Похожие инструкции для RoboRiv

Бренды по названию

Популярные бренды