HS-Technik RoboRiv страница 35 Скачать руководство пользователя | Manualshive

Страница: 35 / 64

background image

- 35 -

Display notification Meaning

Both setting procedures were successful.

Example of the NOK setting process:

Process 1 NOK, 2 processes remaining. The error notification can be

removed by clicking on the yellow button.

The tension is displayed. After sliding the battery the notification

„Trigger“ appears. If the trigger is not released the battery voltage is

displayed.

NOK must be confirmed separately by the worker clicking on the

yellow button on the display.

Maximum temperature of the motor exceeded, consult the manu-

facturer.

Maximum logic voltage exceeded, tool must be repaired!

Maximum permissible force exceeded, consult the manufacturer.

Maximum permissible current exceeded , consult the manufacturer.

Maximum temperature of the control exceeded, consult the manu-

facturer.

«
...
33
34
35
36
37
...
»

Содержание RoboRiv

































































Отзывы:

Нет отзывов

Похожие инструкции для RoboRiv

Бренд: TKR Group Страницы: 64

Бренд: Michigan Pneumatic Tool Страницы: 16

Бренд: CRH Страницы: 16

Бренд: Ober Страницы: 32

Бренд: BGS technic Страницы: 8

Бренд: PELA Страницы: 26

Бренд: Textron Страницы: 4

Бренд: Cembre Страницы: 12

Бренд: COFAN Страницы: 34

Бренд: Festool Страницы: 38

Бренд: ACME Страницы: 2

Бренд: Mannesmann Страницы: 50

Бренд: Franklin Страницы: 16

BEAD BAZOOKA BB10L2

Бренд: Gaither Страницы: 10

Бренд: Rothenberger Страницы: 28

Бренд: K-Rain Страницы: 15

Бренд: 3M Страницы: 8

Бренд: Baileigh Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды