HS-Technik RoboRiv страница 33 Скачать руководство пользователя | Manualshive

Страница: 33 / 64

background image

- 33 -

4.5.1

Display notifications

Display notification Meaning

Battery status: 50 % - 100 %

Battery status: 30 % - 50 %

Battery status: 10 % - 30 %

Battery status: 5 % - 10 %

Battery status: less than 5 %

The tool is ready for use.

The blind rivet nut which was spun on can now be spun off. Hold the

blind rivet nut (not by hand). This option is only possible if a stop is

programmed between the winding and the riveting process.

The tool was successfully restarted. The tool moves into its original

state and checks the tool for functionality by setting the trigger

signal. Then the tool is ready for operation.

1160

Enable

The tool is approved for one blind rivet.

Display settings HST-Tool-Manager:

Signals - OLED display - Standard

«
...
31
32
33
34
35
...
»

Содержание RoboRiv

































































Отзывы:

Нет отзывов

Похожие инструкции для RoboRiv

Бренд: Samson Страницы: 16

Бренд: NORDFOREST Страницы: 274

Бренд: Yost Vises Страницы: 5

Бренд: Würth Страницы: 296

Бренд: Carpenter MFG Страницы: 8

Бренд: Traditional Tool Repair Inc. Страницы: 2

Бренд: ReelCraft Страницы: 5

Бренд: ReelCraft Страницы: 2

Бренд: REED Страницы: 2

Бренд: OYPLA DIY Страницы: 2

Бренд: HIKOKI Страницы: 48

Бренд: Wen Страницы: 12

Бренд: Nancy’s Knit Knacks Страницы: 2

Бренд: YATO Страницы: 88

Бренд: Bahco Страницы: 7

Бренд: Yost Vises Страницы: 5

Бренд: Garland Страницы: 132

Бренд: Band-it Страницы: 15

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды