manualshive.com logo in svg

HPE StoreOnce 3620, Руководство по установке

Поделиться
Скачать
HPE StoreOnce 3620 Скачать руководство пользователя страница 85

WARNING: 

To reduce the risk of personal injury or damage to the equipment, be sure that:

• The leveling jacks are extended to the floor.

• The full weight of the rack rests on the leveling jacks.

• The stabilizing feet are attached to the rack of a single-rack installation.

• Only one component is extended at a time. A rack may become unstable if more than one

component is extended for any reason.

CAUTION: 

Use extreme caution when installing and pulling units from the rack. They can slip and

fall, damaging the StoreOnce System or causing personal injury.

HPE is not responsible for any injury or damage caused by the mishandling of the StoreOnce
System. Always use at least two people to lift and install an enclosure into the rack.

Installing and connecting the capacity upgrade enclosures

Preparing for the installation

Procedure

1.

Unpack the capacity upgrade kit and verify the contents.

See 

StoreOnce 5200 Capacity Upgrade Kit (B964A) contents

.

NOTE: 

For systems where the capacity upgrade kit has been pre-configured at the factory, locate the

label on the rear tab of the unit that identifies its position in the daisy chain sequence of storage
shelves.

2.

Unpack the rail kit. Install the rail kit following the instructions supplied with the rail kit.

IMPORTANT: 

Read the installation guidelines carefully before installing the rails and the

expansion enclosure. The instructions provide important safety information.

NOTE: 

The installation instructions suggest adjusting the back bracket on the standard rail kit after

installing the rails. For ease of installation with the capacity upgrade kit, HPE recommends making the
adjustment prior to mounting the rail kit, as described in the next section.

3.

Identify the rack location for the 2U capacity upgrade kit.

See 

Where to install the enclosure

.

Enabling maintenance mode when using StoreOnce Remote Support

If StoreOnce Remote Support is configured, put the StoreOnce System into maintenance mode before
installing the upgrade. Enabling maintenance mode prevents the system from generating unwanted
support calls during the installation process.

Procedure

1.

Navigate to the StoreOnce System and log in to the StoreOnce Management Console.

2.

On the main menu, select 

Settings

.

Installing capacity upgrade kits

85

Содержание StoreOnce 3620





















































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды