HPE ProLiant DL180 Скачать руководство пользователя страница 171

Страница: 171 / 172

Support and other resources

Accessing Hewlett Packard Enterprise Support

• For live assistance, go to the Contact Hewlett Packard Enterprise Worldwide website:

http://www.hpe.com/assistance

• To access documentation and support services, go to the Hewlett Packard Enterprise Support Center

website:

http://www.hpe.com/support/hpesc

Information to collect

• Technical support registration number (if applicable)

• Product name, model or version, and serial number

• Operating system name and version

• Firmware version

• Error messages

• Product-specific reports and logs

• Add-on products or components

• Third-party products or components

Accessing updates

• Some software products provide a mechanism for accessing software updates through the product

interface. Review your product documentation to identify the recommended software update method.

• To download product updates:

Hewlett Packard Enterprise Support Center

www.hpe.com/support/hpesc

Hewlett Packard Enterprise Support Center: Software downloads

www.hpe.com/support/downloads

Software Depot

www.hpe.com/support/softwaredepot

• To subscribe to eNewsletters and alerts:

www.hpe.com/support/e-updates

• To view and update your entitlements, and to link your contracts and warranties with your profile, go to

the Hewlett Packard Enterprise Support Center

More Information on Access to Support Materials

page:

www.hpe.com/support/AccessToSupportMaterials

Support and other resources

171

Содержание ProLiant DL180













































































































































































Результаты поиска

Содержание ProLiant DL180

Отзывы:

Похожие инструкции для ProLiant DL180

Бренды по названию

Популярные бренды

HPE ProLiant DL180, Руководство пользователя

Результаты поиска

Содержание ProLiant DL180

Отзывы:

Похожие инструкции для ProLiant DL180

Бренды по названию

Популярные бренды