HPE FlexNetwork MSR1002-4 Скачать руководство пользователя страница 140

Страница: 140 / 548

126

ntp-service unicast-peer

Use

ntp-serviceunicast-peer

to specify a symmetric-passive peer for the device.

Use

undo ntp-serviceunicast-peer

to remove the symmetric-passive peer specified for the device.

Syntax

ntp-serviceunicast-peer

{

peer-name

ip-address

} [

vpn-instance vpn-instance-name

]

[

authentication-keyidkeyid

priority

sourceinterface-type interface-number

versionnumber

] *

undontp-serviceunicast-peer

{

peer-name

ip-address

} [

vpn-instancevpn-instance-name

]

Default

No symmetric-passive peer is specified.

Views

System view

Predefined user roles

network-admin

Parameters

peer-name

: Specifies a symmetric-passive peer by its host name, a case-insensitive string of 1 to

253 characters.

ip-address

: Specifies a symmetric-passive peer by its IP address. It must be a unicast address,

rather than a broadcast address, a multicast address, or the IP address of the local clock.

vpn-instancevpn-instance-name

: Specifies the VPN to which the symmetric-passive peer belongs.

The

vpn-instance-name

argument is a case-sensitive string of 1 to 31 characters. If the

symmetric-passive peer is on the public network, do not specify this option.

authentication-keyidkeyid

: Specifies the key ID to be used for sending NTP messages to the peer.

The value range for the

keyid

argument is1 to 4294967295. If you do not specify this option, the local

device and the peer do not authenticate each other.

priority

: Specifies the peer specified by

ip-address

peer-name

as the first choice under the same

condition.

sourceinterface-type interface-number

: Specifies the source interface for NTP messages. In an NTP

message the local device sends to its peer, the source IP address is the primary IP address of this

interface. The

interface-type interface-number

argument represents the interface type and number.If

you do not specify this option, the device searches the routing table for the outgoing interface and

uses the primary IP address of the outgoing interface as the source IP address of the NTP

messages.

versionnumber

: Specifies the NTP version. The value range for the

number

argument is 1 to 4. The

default value is4.

Содержание FlexNetwork MSR1002-4





































































































































































































































































































































































































































































































































































Результаты поиска

Содержание FlexNetwork MSR1002-4

Отзывы:

Похожие инструкции для FlexNetwork MSR1002-4

Бренды по названию

Популярные бренды

HPE FlexNetwork MSR1002-4, Справочник по командам

Результаты поиска

Содержание FlexNetwork MSR1002-4

Отзывы:

Похожие инструкции для FlexNetwork MSR1002-4

Бренды по названию

Популярные бренды