HPE FlexNetwork 7500 Series Скачать руководство пользователя страница 156

Страница: 156 / 430

147

Parameters

max-power

: Sets the maximum power to an integer in the range of 37 to 800, in watts.

pse

pse-id

: Specifies a PSE by its ID.

Usage guidelines

To prevent power supply interruption, the maximum PSE power must be greater than the total
maximum power of all critical PIs.

The total maximum power of PSEs must be smaller than the maximum PoE power.

This command is only available for the default MDC. For more information about MDCs, see

Virtual

Technologies Configuration Guide

Examples

# Set the maximum power to 150 watts for PSE 7.

<Sysname> system-view

[Sysname] poe pse 7 max-power 150

Related commands

poe priority pse

poe mode

Use

poe mode

to configure a PoE power transmission mode.

Use

undo poe mode

to restore the default.

Syntax

poe mode

{

signal

spare

}

undo poe mode

Default

The PoE power transmission mode is

signal

(power over signal cables).

Views

PI view

PoE profile view

Predefined user roles

network-admin

mdc-admin

Parameters

signal

: Specifies the PoE power transmission mode as power over signal cables. The system uses

pairs 1, 2, 3, and 6 in the Category 3 or Category 5 twisted pair cable to supply DC power.

spare

: Specifies the PoE power transmission mode as

power over spare cables. The system uses

pairs 4, 5, 7, and 8 in the Category 3 or Category 5 twisted pair cable to supply DC power. The switch
does not support this keyword.

Examples

# Set the PoE power transmission mode to

power over signal cables in PI view.

<Sysname> system-view

[Sysname] interface gigabitethernet 1/0/1

[Sysname-GigabitEthernet1/0/1] poe mode signal

Содержание FlexNetwork 7500 Series















































































































































































































































































































































































































































Результаты поиска

Содержание FlexNetwork 7500 Series

Отзывы:

Похожие инструкции для FlexNetwork 7500 Series

Бренды по названию

Популярные бренды

HPE FlexNetwork 7500 Series, Справочник команд управления и мониторинга сети

Результаты поиска

Содержание FlexNetwork 7500 Series

Отзывы:

Похожие инструкции для FlexNetwork 7500 Series

Бренды по названию

Популярные бренды