HPE FlexNetwork 10500 SERIES Скачать руководство пользователя страница 148 | Manualshive

Страница: 148 / 407

background image

137

Configuring RMON

Overview

Remote Network Monitoring (RMON) is an enhancement to SNMP. It enables proactive remote
monitoring and management of network devices and subnets. An RMON monitor periodically or
continuously collects traffic statistics for the network attached to a port on the managed device. The
managed device can automatically send a notification when a statistic crosses an alarm threshold,
so the NMS does not need to constantly poll MIB variables and compare the results.

RMON uses SNMP notifications to notify NMSs of various alarm conditions such as broadcast traffic
threshold exceeded. In contrast, SNMP reports function and interface operating status changes such
as link up, link down, and module failure. For more information about SNMP notifications, see
"

Configuring SNMP

HPE devices provide an embedded RMON agent as the RMON monitor. An NMS can perform basic
SNMP operations to access the RMON MIB.

RMON groups

Among standard RMON groups, Hewlett Packard Enterprise implements the statistics group, history
group, event group, alarm group, probe configuration group, and user history group. Hewlett
Packard Enterprise also implements a private alarm group, which enhances the standard alarm
group. The probe configuration group and user history group are not configurable from the CLI. To
configure these two groups, you must access the MIB. For more information about MIB settings for
RMON, see

Comware 7 Platform MIB Companion

.

Statistics group

The statistics group samples traffic statistics for monitored Ethernet interfaces and stores the
statistics in the Ethernet statistics table (ethernetStatsTable). The statistics include:

•

Number of collisions.

•

CRC alignment errors.

•

Number of undersize or oversize packets.

•

Number of broadcasts.

•

Number of multicasts.

•

Number of bytes received.

•

Number of packets received.

The statistics in the Ethernet statistics table are cumulative sums.

History group

The history group periodically samples traffic statistics on interfaces and saves the history samples
in the history table (etherHistoryTable). The statistics include:

•

Bandwidth utilization.

•

Number of error packets.

•

Total number of packets.

The history table stores traffic statistics collected for each sampling interval.

«
...
146
147
148
149
150
...
»

Содержание FlexNetwork 10500 SERIES
























































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для FlexNetwork 10500 SERIES

TokenLink 3C359B

Бренд: 3Com Страницы: 4

TokenLink 3C359B

Бренд: 3Com Страницы: 8

TokenLink 3C339

Бренд: 3Com Страницы: 2

EtherLink 3C985B-SX

Бренд: 3Com Страницы: 44

Бренд: 3Com Страницы: 88

Бренд: 3Com Страницы: 2

Бренд: 3Com Страницы: 111

TokenLink 3C359

Бренд: 3Com Страницы: 4

Бренд: 3Com Страницы: 74

Бренд: 3Com Страницы: 6

Бренд: Abocom Страницы: 11

Бренд: Abocom Страницы: 19

Бренд: D-Link Страницы: 83

Бренд: NetBurner Страницы: 15

Sentry Global Security Modem

Бренд: Server Technology Страницы: 22

HomePlug AV Ethernet Bridge PLE0200

Бренд: Abocom Страницы: 2

Бренд: Qixiang Technology Страницы: 16

Бренд: Sangamo Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды