HPE 3PAR StoreServ Скачать руководство пользователя

Страница: 50 / 174

13. Only to be completed by a certified electrician provided by the customer:

Install the power

cable on the -48V DC PCMs and re-engage power from the fuse/distribution panel.

WARNING:

Before powering up the storage system, a certified electrician must attach all the

power cabling to all the PCMs.

The power cable is connected to the -48V DC PCM with connections to the positive terminal ( ),
negative terminal ( ), and ground terminal ( ).

Verification

14.

Verify that the replacement DC PCM has been successfully installed.

Turn on the PCM and check that the power LED is on.

15.

Stop the

Locate

action on the drive enclosure.

At the right side of the

Schematic

view of the drive enclosure, click the UID icon.

16.

After the component replacement, initiate

Check Health

on the storage system.

From the Service Console interface, select

Systems

Select

Actions

Check health

17.

If significant time is left in the maintenance window, end the

Maintenance Mode

From the Service Console interface, select

Systems

Select

Actions

Set maintenance mode

To end the maintenance window associated with the replacement, click

The flow of support information and local notifications of system alerts will be sent to Hewlett
Packard Enterprise again.

18.

Follow the return instructions provided with the replacement component.

SFP transceiver replacement

Replacing an SFP transceiver—SP 4.x

This procedure is for the replacement of a small form-factor pluggable (SFP) transceiver using HPE 3PAR
Service Processor (SP) 4.x. An SFP transceiver is installed in each onboard Fibre Channel (FC) port and
in the ports of host adapters.

WARNING:

When the storage system is on, do not stare at the FC fibers because doing so could

damage your eyes.

CAUTION:

To prevent damage when handling the SFP transceiver, do not touch the gold contact

leads.

IMPORTANT:

All SFP ports must contain an SFP transceiver and cable or a dust cover.

Service

Содержание 3PAR StoreServ















































































































































































Результаты поиска

Содержание 3PAR StoreServ

Отзывы:

Похожие инструкции для 3PAR StoreServ

Бренды по названию

Популярные бренды

HPE 3PAR StoreServ, Руководство по обслуживанию и модернизации

Результаты поиска

Содержание 3PAR StoreServ

Отзывы:

Похожие инструкции для 3PAR StoreServ

Бренды по названию

Популярные бренды