HPE 3PAR StoreServ Скачать руководство пользователя

Страница: 130 / 174

LED function

Status

State

Red flashing

System critical

If the health LED indicates a degraded or critical state, review the
system IML or use iLO to review the system health status.

NIC status
LED*

Green solid

Link to network

Green flashing

Network active

Off

No network activity

*When all four LEDs described in this table flash simultaneously, a power fault has occurred.

System status LEDs

This information applies only to the HPE 3PAR StoreServ 8000 Storage system. The controller node
enclosures and drive enclosures have system status LEDs at the front, left corner of the enclosures.

Figure 112: System status LEDs, left bezel ear cap, SFF enclosures front view

Table 41: System status LEDs, left bezel ear cap, SFF enclosures front view

LED

Function

Status

State

System power

Green solid

Power

Off

No power

System standby

Amber solid

Enclosure powered by the battery

Module fault

Amber solid

Fault

Off

No fault

Table Continued

130

More information

Содержание 3PAR StoreServ















































































































































































Результаты поиска

Содержание 3PAR StoreServ

Отзывы:

Похожие инструкции для 3PAR StoreServ

Бренды по названию

Популярные бренды

HPE 3PAR StoreServ, Руководство по обслуживанию и модернизации

Результаты поиска

Содержание 3PAR StoreServ

Отзывы:

Похожие инструкции для 3PAR StoreServ

Бренды по названию

Популярные бренды