HP XP Скачать руководство пользователя страница 24

Страница: 24 / 148

Table 3 Support scope of RSG assignment of each resource (continued)

Support

Privilege for RSG

RSG Assignment

Resource

Non-Supported

With privilege

Different RSG from
P-VOL

Non-Supported

Without privilege

Supported

With privilege

Same RSG as P-VOL

Host group ID

Non-Supported

Without privilege

Non-Supported

With privilege

Different RSG from
P-VOL

Non-Supported

Without privilege

Supported

With privilege

Same RSG as P-VOL

Pool (THP/Smart/FS)

Non-Supported

Without privilege

Supported

With privilege

Different RSG from
P-VOL

Non-Supported

Without privilege

Pool is not managed by RSG. However, a pool created only by LDEV which belongs to specific RSG can only be used

by a user who has RSG privileges.

NOTE:

Even if P-VOL to be operated is assigned in meta_resource, it can be used if a user

has appropriate privileges.

Placement location of command device which is connected to host

Place a command device in each physical DKC when a command device is used in multiple
virtual DKCs.

Table 4 Support scope of placement location of command device which is connected to
host

Remarks

Support

Placement location

Supported

Only command device in physical
DKC

Connecting only command device in
physical DKC to host is required.

Non-Supported

Only command device in virtual DKC

Same as above.

Non-Supported

Command device in physical DKC
and virtual DKC

Support scope of HA configuration

This subsection indicates the support scope of HA configuration.

Adapter function

Table 5 Support scope of adapter function

Remarks

Support

Function

Target

Supported

Creation of secondary VOL

Primary site only

Supported

Removal of secondary VOL

Supported

Secondary VOL pair
operations

Supported

Secondary VOL mapping

Environmental Prerequisites

Содержание XP





















































































































































Результаты поиска

Содержание XP

Отзывы:

Похожие инструкции для XP

Бренды по названию

Популярные бренды

HP XP, Руководство пользователя

Результаты поиска

Содержание XP

Отзывы:

Похожие инструкции для XP

Бренды по названию

Популярные бренды