HP StorageWorks A7298A Скачать руководство пользователя страница 45 | Manualshive

Страница: 45 / 82

background image

host bus adapter for Windows and Linux installation guide

4–7

Troubleshooting

SCSI Address Mapping

The driver emulates six SCSI buses per HBA to map all 126 possible AL_PA to Target
IDs.

The first bus is a dummy bus used to delay the initial inquiry scan until after discovery
completes. The 31 target IDs per bus are then mapped to either ascending or
descending SEL_IDs (based on the ScanDown registry parameter).

NOTE: The driver uses the first bus if the parameter MapBus0=1 is used.

Fabric Device Mapping

In a fabric (switched) environment, devices are initially created in the order that they
are returned from the Simple Name Server (SNS). Once created (at boot), the devices
continue to be tracked based on:

–WWPN:HardAddress=0;MapNodeName=0
–NodeName:HardAddress=0;MapNodeName=1
–D_ID:HardAddress=1; (MapNodeName=don’t care)

0x22

IOERR_RESERVED

0x23

IOERR_RESERVED

0x24

IOERR_RESERVED

0x25

IOERR_ABORT_MULTI_REQUESTED

0x26

IOERR_RESERVED

0x27

IOERR_RESERVED

0x28

IOERR_LINK_BUFFER_SHORTAGE

0x29

IOERR_RCV_XRIBUF_WAITING

Table 4–4: Parameter Error Values Valid only when CmdStat=0x3 (Continued)

0x12 Offset

Explanation (Continued)

«
...
43
44
45
46
47
...
»

Содержание StorageWorks A7298A



















































































Отзывы:

Нет отзывов

Похожие инструкции для StorageWorks A7298A

Бренд: Pace Страницы: 15

Бренд: VSmart Страницы: 9

Бренд: TRENDnet Страницы: 15

Бренд: Hama Страницы: 22

Бренд: FirmTek Страницы: 30

iSYSTEM NXP S32K148

Бренд: TASKING Страницы: 20

Бренд: StarTech.com Страницы: 17

Бренд: Siemens Страницы: 4

Бренд: Philips Страницы: 2

Бренд: NETGEAR Страницы: 2

Бренд: NETGEAR Страницы: 20

Бренд: Belkin Страницы: 24

Бренд: D Line Страницы: 37

Бренд: Comcast Страницы: 4

Бренд: Audison Страницы: 2

Бренд: Abocom Страницы: 62

Бренд: Iron logic Страницы: 9

Бренд: EDUP Страницы: 18

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды