HP ProLiant XL270d Gen9 Скачать руководство пользователя страница 89

Страница: 89 / 126

13.

Install the DIMMS.

14.

Install the PCI riser modules.

15.

Install the power riser.

16.

Install the riser cross bracket.

17.

Install the HPE Smart Array P542D controller module.

18.

Install the expansion board.

19.

Connect all cables disconnected from the PCI riser modules and the failed system board.

20.

Install the drive cage assembly.

21.

Connect all cables to the drive backplane.

22.

Install all GPUs and GPU blanks.

23.

Install the side panels.

24.

Install the air baffle.

25.

If the 4:1 riser cable signal or Smart Storage Battery are installed in the air baffle, reconnect the
cable to the risers. For more information, see "Cabling (

Storage cabling

)".

26.

Install the access panel.

27.

Install the server into the chassis.

28.

Connect all peripheral cables to the server .

29.

Press the Power On/Standby button.

The server exits standby mode and applies full power to the system. The system power LED
changes from amber to green.

HP Trusted Platform Module

The TPM is not a customer-removable part.

HP Trusted Platform Module

Содержание ProLiant XL270d Gen9































































































































Результаты поиска

Содержание ProLiant XL270d Gen9

Отзывы:

Похожие инструкции для ProLiant XL270d Gen9

Бренды по названию

Популярные бренды

HP ProLiant XL270d Gen9, Руководство по техническому обслуживанию и ремонту

Результаты поиска

Содержание ProLiant XL270d Gen9

Отзывы:

Похожие инструкции для ProLiant XL270d Gen9

Бренды по названию

Популярные бренды