manualshive.com logo in svg

HP ProLiant DL785, Руководство пользователя, Страница: 13 / 110

Поделиться
Скачать
HP ProLiant DL785 Скачать руководство пользователя страница 13

Interpretation

Fault/UID LED
(amber/blue)

Online/activity LED
(green)

The drive is online, but is not currently active.

Off

On

CAUTION:

Do not remove the drive. Removing a drive can terminate the

current operation and cause data loss.
The drive is part of an array that is undergoing capacity expansion or stripe
migration, but a predictive failure alert has been received for this drive. To
minimize the risk of data loss, do not replace the drive until the expansion
or migration is complete.

Flashing amber
(1Hz)

Flashing (1 Hz)

CAUTION:

Do not remove the drive. Removing a drive can terminate the

current operation and cause data loss.
The drive is rebuilding, or it is part of an array that is undergoing capacity
expansion or stripe migration.

Off

Flashing (1 Hz)

The drive is active, but a predictive failure alert has been received for this
drive. Replace the drive as soon as possible.

Flashing amber
(1Hz)

Flashing
irregularly

The drive is active and is operating normally.

Off

Flashing
irregularly

A critical fault condition has been identified for this drive and the controller
has placed it offline. Replace the drive as soon as possible.

Solid amber

Off

A predictive failure alert has been received for this drive. Replace the drive
as soon as possible.

Flashing amber
(1Hz)

Off

The drive is: offline, a spare, or not configured as part of an array.

Off

Off

Processor memory cell components

Description

Item

DIMM slot 1A

1

DIMM slot 2A

2

DIMM slot 3B

3

DIMM slot 4B

4

DIMM slot 5C

5

Processor memory cell components

13

Содержание ProLiant DL785















































































































Отзывы:

Нет отзывов