HP ProLiant DL60 Gen9 Скачать руководство пользователя страница 98

Страница: 98 / 127

Software and configuration utilities 98

•

Supports online array capacity expansion, logical drive extension, assignment of online spares, and

RAID or stripe size migration

•

Provides diagnostic and SmartSSD Wear Gauge functionality on the Diagnostics tab

•

For supported controllers, provides access to additional features.

For more information about HPE SSA, see the Hewlett Packard Enterprise website

(

http://www.hpe.com/servers/ssa

Automatic Server Recovery

ASR is a feature that causes the system to restart when a catastrophic operating system error occurs,

such as a blue screen, ABEND, or panic. A system fail-safe timer, the ASR timer, starts when the System

Management driver, also known as the Health Driver, is loaded. When the operating system is functioning

properly, the system periodically resets the timer. However, when the operating system fails, the timer

expires and restarts the server.
ASR increases server availability by restarting the server within a specified time after a system hang. You

can disable ASR from the System Management Homepage or through UEFI System Utilities.

USB support

Hewlett Packard Enterprise provides both standard USB 2.0 support and legacy USB 2.0 support.

Standard support is provided by the OS through the appropriate USB device drivers. Before the OS loads,

Hewlett Packard Enterprise provides support for USB devices through legacy USB support, which is

enabled by default in the system ROM.
Legacy USB support provides USB functionality in environments where USB support is not available

normally. Specifically, Hewlett Packard Enterprise provides legacy USB functionality for the following:

•

POST (system boot)

•

UEFI System Utilities

•

Pre-boot UEFI shell

•

DOS

•

Operating environments which do not provide native USB support

External USB functionality

Hewlett Packard Enterprise provides external USB support to enable local connection of USB devices for

server administration, configuration, and diagnostic procedures.
For additional security, external USB functionality can be disabled through USB options in UEFI System

Utilities.

Redundant ROM support

The server enables you to upgrade or configure the ROM safely with redundant ROM support. The server

has a single ROM that acts as two separate ROM images. In the standard implementation, one side of the

ROM contains the current ROM program version, while the other side of the ROM contains a backup

version.

NOTE:

The server ships with the same version programmed on each side of the ROM.

Содержание ProLiant DL60 Gen9
































































































































Результаты поиска

Содержание ProLiant DL60 Gen9

Отзывы:

Похожие инструкции для ProLiant DL60 Gen9

Бренды по названию

Популярные бренды

HP ProLiant DL60 Gen9, Руководство пользователя

Результаты поиска

Содержание ProLiant DL60 Gen9

Отзывы:

Похожие инструкции для ProLiant DL60 Gen9

Бренды по названию

Популярные бренды