HP ProLiant DL60 Gen9 Скачать руководство пользователя страница 96

Страница: 96 / 127

Software and configuration utilities 96

For more information, see the

HPE UEFI System Utilities User Guide for HPE ProLiant Gen9 Servers

the Hewlett Packard Enterprise website (

http://www.hpe.com/info/uefi/docs

Restoring and customizing configuration settings

You can reset all configuration settings to the factory default settings, or you can restore system default

configuration settings, which are used instead of the factory default settings.
You can also configure default settings as necessary, and then save the configuration as the custom

default configuration. When the system loads the default settings, it uses the custom default settings

instead of the factory defaults.

Secure Boot configuration

Secure Boot is integrated in the UEFI specification on which the Hewlett Packard Enterprise

implementation of UEFI is based. Secure Boot is completely implemented in the BIOS and does not

require special hardware. It ensures that each component launched during the boot process is digitally

signed and that the signature is validated against a set of trusted certificates embedded in the UEFI BIOS.

Secure Boot validates the software identity of the following components in the boot process:

•

UEFI drivers loaded from PCIe cards

•

UEFI drivers loaded from mass storage devices

•

Pre-boot UEFI shell applications

•

OS UEFI boot loaders

Once enabled, only firmware components and operating systems with boot loaders that have an

appropriate digital signature can execute during the boot process. Only operating systems that support

Secure Boot and have an EFI boot loader signed with one of the authorized keys can boot when Secure

Boot is enabled. For more information about supported operating systems, see the

HPE UEFI System

Utilities and Shell Release Notes for HPE ProLiant Gen9 Servers

on the Hewlett Packard Enterprise

website (

http://www.hpe.com/info/uefi/docs

A physically present user can customize the certificates embedded in the UEFI BIOS by adding/removing

their own certificates.
When Secure Boot is enabled, the System Maintenance Switch does not restore all manufacturing

defaults when set to the ON position. For security reasons, the following are not restored to defaults when

the System Maintenance Switch is in the ON position:

•

Secure Boot is not disabled and remains enabled.

•

The Boot Mode remains in UEFI Boot Mode even if the default boot mode is Legacy Boot Mode.

•

The Secure Boot Database is not restored to its default state.

•

iSCSI Software Initiator configuration settings are not restored to defaults.

Embedded UEFI shell

The system BIOS in all ProLiant Gen9 servers includes an Embedded UEFI Shell in the ROM. The UEFI

Shell environment provides an API, a command line prompt, and a set of CLIs that allow scripting, file

manipulation, and system information. These features enhance the capabilities of the UEFI System

Utilities.
For more information, see the following documents:

•

HPE UEFI Shell User Guide for HPE ProLiant Gen9 Servers

on the Hewlett Packard Enterprise

website (

http://www.hpe.com/info/uefi/docs

)

•

UEFI Shell Specification

on the UEFI website (

http://www.uefi.org/specifications

)

Содержание ProLiant DL60 Gen9
































































































































Результаты поиска

Содержание ProLiant DL60 Gen9

Отзывы:

Похожие инструкции для ProLiant DL60 Gen9

Бренды по названию

Популярные бренды

HP ProLiant DL60 Gen9, Руководство пользователя

Результаты поиска

Содержание ProLiant DL60 Gen9

Отзывы:

Похожие инструкции для ProLiant DL60 Gen9

Бренды по названию

Популярные бренды