HP ProCurve 8116fl Скачать руководство пользователя страница 20

Страница: 20 / 134

trodu

cin

the

ProCurve

Series 8100fl Switch

Introducing the ProCurve Series 8100fl Switch

Front of the Switch

Table 1-5.

10-Port mini-GBIC Module (J8735A) LEDs

The 10-Port mini-GBIC Module shows the activity status of each port on top
and has an LED showing the link status of each port on the bottom.

10-Port mini-GBIC Module

LED

Color

State

Meaning

Ports 1-4

Activity and
Link LEDs
(per port)

Activity
(per port)

Green

Off

Flashing

Solid

Flashing

Transmitting data.

Link is up; no data is being transferred.

When no connector is plugged into the
port, the LED will flash approximately
once every four seconds. This is a safety
feature known as Auto Laser Shutdown

Ports 5-8

Link
(per port)

Green

n/a

Solid

Off

Link is up.

No connector is plugged into the port.

Ports 9-10

Status LED

Status

n/a

Green

Yellow/
Orange

Off

Flashing

Solid

Flashing

No power to the module.

Module is powering up and downloading
operating software.

Software image loaded successfully.

Self-test failure.

N o t e

The 10-Port mini-GBIC Module supports various ProCurve mini-GBICs. Refer
to the

ProCurve Switch fl Modules Installation Guide

for further details.

1-10

Содержание ProCurve 8116fl







































































































































Результаты поиска

Содержание ProCurve 8116fl

Отзывы:

Бренды по названию

Популярные бренды

HP ProCurve 8116fl, Руководство по установке и началу работы

Результаты поиска

Содержание ProCurve 8116fl

Отзывы:

Бренды по названию

Популярные бренды