HP ProCurve 8116fl Скачать руководство пользователя страница 19

Страница: 19 / 134

Introducing the ProCurve Series 8100fl Switch

Front of the Switch

Table 1-4.

10-Port 100/1000Base-T Module (J8734A) LEDs

The 10-Port 100/1000 Base-T Module shows the link status of each port on top
and has an LED showing the activity status of each port on the bottom.

10-Port 100/1000Base-T
Module

LED

Color

State

Meaning

Ports 1-4

Link and
Activity LEDs
(per port)

Link
(per port)

Green

Amber

n/a

Solid

Off

Port is in 1000 Mbps mode.

Port is in 100 Mbps mode.

No connector is plugged into the port.

Ports 5-6

Activity
(per port)

Green

n/a

Flashing

Off

Transmitting data.

No data is being transferred, and/or no
connector is plugged into the port.

Ports 7-10

Status LED

Status

n/a

Green

Yellow/
Orange

Off

Flashing

Solid

Flashing

No power to the module.

Module is powering up and downloading
operating software.

Software image loaded successfully.

Self-test failure.

Int
rod
uci
ng th

e ProCurve

Series 8100fl Switch

1-9

Содержание ProCurve 8116fl







































































































































Результаты поиска

Содержание ProCurve 8116fl

Отзывы:

Бренды по названию

Популярные бренды

HP ProCurve 8116fl, Руководство по установке и началу работы

Результаты поиска

Содержание ProCurve 8116fl

Отзывы:

Бренды по названию

Популярные бренды