HP ProCurve 8116fl Скачать руководство пользователя страница 103 | Manualshive

Страница: 103 / 134

HP ProCurve 8116fl Скачать руководство пользователя страница 103

Switch Ports and Network Cables

B

Switch Ports and Network Cables

This appendix includes switch connector information and network cable
information for cables that should be used with ProCurve 8100fl switches,
including minimum pin-out information and specifications for twisted-pair
cables.

N o t e

Incorrectly wired cabling is the most common cause of problems for LAN
communications. ProCurve Networking recommends that you work with a
qualified LAN cable installer for assistance with your cabling requirements.

Switch Ports and Connectors

Twisted Pairs

■

The RJ-45 ports on the

100/1000-T Interface Module

and the single

10/100Base-T

Ethernet port on the management module accept 100-ohm

differential unshielded and shielded twisted-pair cable with RJ-45 connec
tors as described on

.

■

The

1000Base-T RJ-45

connectors on the 1

000Base-T mini-GBIC

(J8177B) are compatible with the IEEE 802.3ab 1000Base-T standards,
and accept 1000 Mbps cables as described in

Fiber-Optic

■

The LC-type connector port on the

Gigabit-SX mini-GBIC

transmits at

850 nm wavelength, and accepts the low metal content, multimode fiber-
optic cables for Gigabit-SX described on

■

The LC-type connector port on the

Gigabit-LX and LH mini-GBIC

transmits at 1310 nm wavelength, and accepts the low metal content,
single-mode or multimode fiber-optic cables for Gigabit-LX described on

.

Swit

ch Ports an

d Net

w

ork

Ca
bles

B-1

«
...
101
102
103
104
105
...
»

Содержание ProCurve 8116fl







































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды