HP photosmart 850 Скачать руководство пользователя

Страница: 99 / 136

<Sysname> system-view

[Sysname] interface Vlan-interface 1

[Sysname-Vlan-interface1] pppoe-server bind virtual-template 1

pppoe-server log-information off

Use

pppoe-server log-information off

to disable PPP log displaying on a device operating as a PPPoE

server.
Use

undo pppoe-server log-information off

to restore the default.

Syntax

pppoe-server log-information off
undo pppoe-server log-information off

Default

PPP log displaying is enabled on a PPPoE server.

Views

System view

Default command level

2: System level

Usage guidelines

With PPP log displaying enabled, large amounts of log information can affect device performance and

be a nuisance to users during configuration. You can disable PPP log displaying by using the

pppoe-server log-information off

command.

Examples

# Disable PPP log displaying.

<Sysname> system-view

[Sysname] pppoe-server log-information off

pppoe-server max-sessions local-mac

Use

pppoe-server max-sessions local-mac

to set the maximum number of PPPoE sessions allowed with

regard to the local MAC address on a device operating as a PPPoE server.
Use

undo pppoe-server max-sessions local-mac

to restore the default.

Syntax

pppoe-server max-sessions local-mac

number

undo

pppoe-server max-sessions local-mac

Default

The maximum number of PPPoE sessions allowed with regard to the local MAC address is 100.

Views

System view

Содержание photosmart 850









































































































































Результаты поиска

Содержание photosmart 850

Отзывы:

Похожие инструкции для photosmart 850

Бренды по названию

Популярные бренды

HP photosmart 850, Справочник по командам

Результаты поиска

Содержание photosmart 850

Отзывы:

Похожие инструкции для photosmart 850

Бренды по названию

Популярные бренды