HP photosmart 850 Скачать руководство пользователя

Страница: 89 / 136

Layer 2 forwarding configuration commands

Normal Layer 2 forwarding configuration

commands

display mac-forwarding statistics

Use

display mac-forwarding statistics

to display Layer 2 forwarding statistics.

Syntax

display mac-forwarding statistics

[

interface

interface-type interface-number

] [

{

begin

exclude

include

}

regular-expression

]

Views

Any view

Default command level

1: Monitor level

Parameters

interface

interface-type interface-number:

Displays the statistics of an interface specified by its type and

number.

: Filters command output by specifying a regular expression. For more information about regular

expressions, see

Fundamentals Configuration Guide

begin

: Displays the first line that matches the specified regular expression and all lines that follow.

exclude

: Displays all lines that do not match the specified regular expression.

include

: Displays all lines that match the specified regular expression.

regular-expression

: Specifies a regular expression, a case-sensitive string of 1 to 256 characters.

Usage guidelines

If no parameter is specified, Layer 2 forwarding statistics for all interfaces is displayed.

Examples

# Display the Layer 2 forwarding statistics for all interfaces.

<Sysname> display mac-forwarding statistics

Total received: 888

Filtered:111 STP discarded:0

Broadcast:0 Multicast:0

Unknown Unicast:0 Invalid Tag:0

Total deliver to up: 111

L2 protocol:11 Local MAC address:100

Содержание photosmart 850









































































































































Результаты поиска

Содержание photosmart 850

Отзывы:

Похожие инструкции для photosmart 850

Бренды по названию

Популярные бренды

HP photosmart 850, Справочник по командам

Результаты поиска

Содержание photosmart 850

Отзывы:

Похожие инструкции для photosmart 850

Бренды по названию

Популярные бренды