HP photosmart 850 страница 81 Скачать руководство пользователя

Страница: 81 / 136

The

bridge-aggregation

keyword is available only when Layer 2 aggregate interfaces exist on the

device.

Examples

# Display detailed information about Layer 2 aggregation group 1, which is a static aggregation group.

<Sysname> display link-aggregation verbose bridge-aggregation 1

Loadsharing Type: Shar -- Loadsharing, NonS -- Non-Loadsharing

Port Status: S -- Selected, U -- Unselected

Aggregation Interface: Bridge-Aggregation1

Aggregation Mode: Static

Loadsharing Type: Shar

Port Status Priority Oper-Key

--------------------------------------------------------------------------------

XGE1/0/1 S 32768 1

XGE1/0/2 S 32768 1

Table 18

Command output

Field

Description

Loadsharing Type

Load sharing type:

•

Shar

—Load sharing.

•

NonS

—Non-load sharing.

Port Status

Port state:

•

—Selected.

•

—Unselected.

Aggregation Interface

Name of the aggregate interface.

Port

Port type and number.

Status

Port state: Selected or Unselected.

Priority

Port aggregation priority.

Oper-Key Operational

key.

enable snmp trap updown

Use

enable snmp trap updown

to enable linkUp/linkDown trap generation for an aggregate interface.

Use

undo enable snmp trap updown

to disable linkUp/linkDown trap generation for an aggregate

interface.

Syntax

enable snmp trap updown
undo enable snmp trap updown

Default

LinkUp/linkDown trap generation is enabled for an aggregate interface.

Views

Layer 2 aggregate interface view

Содержание photosmart 850









































































































































Результаты поиска

Содержание photosmart 850

Отзывы:

Похожие инструкции для photosmart 850

Бренды по названию

Популярные бренды

HP photosmart 850, Справочник по командам

Результаты поиска

Содержание photosmart 850

Отзывы:

Похожие инструкции для photosmart 850

Бренды по названию

Популярные бренды