HP photosmart 850 Скачать руководство пользователя

Страница: 73 / 136

Ethernet link aggregation configuration
commands

Support for this feature depends on the device model. For more information, see

About the Command

References for HP Unified Wired-WLAN Products

default

Use

default

to restore the default settings for an aggregate interface.

Syntax

default

Views

Layer 2 aggregate interface view

Default command level

2: System level

Usage guidelines

CAUTION:

The

default

command might interrupt ongoing network services. Make sure you are fully aware of the

impacts of this command when you execute it on a live network.

This command might fail to restore the default settings for some commands for reasons such as command

dependencies and system restrictions. Use the

display this

command in interface view to identify these

commands, and then use their

undo

forms or follow the command reference to restore their default

settings. If your restoration attempt still fails, follow the error message instructions to resolve the problem.

Examples

# Restore the default settings for Layer 2 aggregate interface Bridge-Aggregation 1.

<Sysname> system-view

[Sysname] interface bridge-aggregation 1

[Sysname-Bridge-Aggregation1] default

This command will restore the default settings. Continue? [Y/N]:y

description

Use

description

to set a description for an interface. For example, you can include information such as

the purpose of the interface for ease of management.
Use

undo description

to restore the default.

Syntax

description

text

Содержание photosmart 850









































































































































Результаты поиска

Содержание photosmart 850

Отзывы:

Похожие инструкции для photosmart 850

Бренды по названию

Популярные бренды

HP photosmart 850, Справочник по командам

Результаты поиска

Содержание photosmart 850

Отзывы:

Похожие инструкции для photosmart 850

Бренды по названию

Популярные бренды