HP photosmart 850 Скачать руководство пользователя | Manualshive

Страница: 70 / 136

background image

65

•

You might need to disable MAC address learning to prevent the MAC address table from being

saturated. For example, when your device is being attacked by many packets with different source
MAC addresses, it affects the update of the MAC address table.

•

Because disabling MAC address learning might result in broadcast storms, enable broadcast storm
suppression after you disable MAC address learning on an interface.

Examples

# Disable global MAC address learning.

<Sysname> system-view

[Sysname] mac-address mac-learning disable

# Disable MAC address learning on Ten-GigabitEthernet 1/0/1.

<Sysname> system-view

[Sysname] interface Ten-GigabitEthernet 1/0/1

[Sysname-Ten-GigabitEthernet1/0/1] mac-address mac-learning disable

# Disable MAC address learning on Bridge-Aggregation 1.

<Sysname> system-view

[Sysname] interface bridge-aggregation 1

[Sysname-Bridge-Aggregation1] mac-address mac-learning disable

Related commands

display mac-address mac-learning

mac-address max-mac-count

Use

mac-address max-mac-count

count

to configure the maximum number of MAC addresses that can

be learned on an interface.
Use

mac-address max-mac-count disable-forwarding

to disable the device from forwarding frames with

unknown source MAC addresses when the upper limit is reached.
Use

undo mac-address max-mac-count

to restore the default maximum number of MAC addresses that

can be learned on an Ethernet interface.
Use

undo mac-address max-mac-count disable-forwarding

to allow the device to forward frames

received on an Ethernet interface with unknown source MAC addresses when the upper limit is reached.

Syntax

mac-address max-mac-count

{

count

|

disable-forwarding

}

undo mac-address max-mac-count

[

disable-forwarding

]

Default

The maximum number of MAC addresses that can be learned on an interface varies with device models.

Frames received are forwarded when the upper limit is reached.

Views

Layer 2 Ethernet interface view, port group view, Layer 2 aggregate interface view

Default command level

2: System level

«
...
68
69
70
71
72
...
»

Содержание photosmart 850









































































































































Отзывы:

Нет отзывов

Похожие инструкции для photosmart 850

Бренд: Samsung Страницы: 2

Бренд: Olympus Страницы: 73

Бренд: Olympus Страницы: 74

Бренд: Canon Страницы: 43

Powershot SD1100 IS

Бренд: Canon Страницы: 227

PowerShot SD950 IS Digital ELPH

Бренд: Canon Страницы: 427

STYLUS TOUGH-8000

Бренд: Olympus Страницы: 86

Бренд: Neoline Страницы: 19

Бренд: IBASE Technology Страницы: 50

Бренд: Papago Страницы: 9

Бренд: Navaio Страницы: 58

Бренд: Vivitar Страницы: 68

Бренд: VADDIO Страницы: 69

Бренд: Covert Systems Страницы: 3

Бренд: BELL+HOWELL Страницы: 3

20MP Waterproof/ Shockproof Digital Camera

Бренд: Ivation Страницы: 2

Бренд: Connects2 Страницы: 2

Бренд: Marshall Electronics Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды