HP photosmart 850 Скачать руководство пользователя | Manualshive

Страница: 57 / 136

background image

52

[Sysname-Bridge-Aggregation1] port trunk permit vlan 2

Please wait... Done.

Configuring Ten-GigabitEthernet1/0/1... Done.

Configuring Ten-GigabitEthernet1/0/2... Done.

The output shows that Ten-GigabitEthernet 1/0/1 and Ten-GigabitEthernet 1/0/2 are the member ports

of the aggregation group corresponding to Bridge-Aggregation 1.

Related commands

port link-type

port trunk pvid

Use

port trunk pvid

to configure the PVID for the trunk port.

Use

undo port trunk pvid

to restore the default.

Syntax

port trunk pvid vlan

vlan-id

undo port trunk pvid

Default

The PVID of a trunk port is VLAN 1.

Views

Ethernet interface view, port group view, Layer 2 aggregate interface view

Default command level

2: System level

Parameters

vlan-id

: Specifies a VLAN ID in the range of 1 to 4094.

Usage guidelines

You can use a nonexistent VLAN as the PVID for a trunk port. If you use the

undo vlan

command to

remove the PVID of a trunk port, it does not affect the setting of the PVID on the port.
The local and remote trunk ports must use the same PVID for the traffic of the PVID to be transmitted

properly.
You must use the

port trunk permit vlan

command to configure the trunk port to allow and forward

packets from the PVID.
The configuration made in Ethernet interface view applies only to the port.
The configuration made in port group view applies to all ports in the port group.
The configuration made in Layer 2 aggregate interface view applies to the aggregate interface and its

aggregation member ports.

•

If the system fails to apply the configuration to the aggregate interface, it stops applying the
configuration to aggregation member ports.

•

If the system fails to apply the configuration to an aggregation member port, it skips the port and
moves to the next member port.

«
...
55
56
57
58
59
...
»

Содержание photosmart 850









































































































































Отзывы:

Нет отзывов

Похожие инструкции для photosmart 850

Бренд: Canon Страницы: 22

PowerShot S400 Digital Elph

Бренд: Canon Страницы: 2

PowerShot S230 DIGITAL ELPH

Бренд: Canon Страницы: 2

PowerShot S110 Digital ELPH

Бренд: Canon Страницы: 7

Бренд: Canon Страницы: 9

PowerShot SD10 Digital ELPH

Бренд: Canon Страницы: 2

PowerShot S400 Digital Elph

Бренд: Canon Страницы: 138

Бренд: Canon Страницы: 186

Бренд: Canon Страницы: 106

PowerShot SD100

Бренд: Canon Страницы: 21

PowerShot S3 IS Digital Camera

Бренд: Canon Страницы: 27

Бренд: Canon Страницы: 15

PowerShot S3 IS Digital Camera

Бренд: Canon Страницы: 2

Бренд: Canon Страницы: 15

Бренд: Samsung Страницы: 44

Бренд: Ganz Thermal Страницы: 2

Бренд: Olympus Страницы: 61

Бренд: Olympus Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды