HP photosmart 850 страница 35 Скачать руководство пользователя

Страница: 35 / 136

Parameters

interface-number

: Specifies a loopback interface by its number. The loopback interface number is

always 0.

Usage guidelines

Clear the existing statistics on the interface before starting to collect new traffic statistics.
If you do not specify the

loopback

keyword, this command clears the statistics on all interfaces in the

system.
If you specify the

loopback

keyword without the

interface-number

argument, this command clears the

statistics on all loopback interfaces.

Examples

# Clear statistics on loopback interface Loopback 0.

<Sysname> reset counters interface loopback 0

reset counters interface null

Use

reset counters interface null

to clear statistics on the null interface.

Syntax

reset counters interface

[

null

[

] ]

Views

User view

Default command level

2: System level

Parameters

: Specifies a null interface by its number, which is always 0.

Usage guidelines

Clear the existing statistics on the interface before starting to collect new traffic statistics.
If you do not specify the

null

keyword, this command clears statistics on all interfaces.

If you specify the

null

keyword, this command clears the statistics on interface Null 0 with or without the

keyword, because the device supports only one interface Null 0.

Examples

# Clear statistics for interface Null 0.

<Sysname> reset counters interface null 0

shutdown

Use

shutdown

to shut down the current loopback interface.

Use

undo shutdown

to bring up the current loopback interface.

Syntax

shutdown
undo shutdown

Содержание photosmart 850









































































































































Результаты поиска

Содержание photosmart 850

Отзывы:

Похожие инструкции для photosmart 850

Бренды по названию

Популярные бренды

HP photosmart 850, Справочник по командам

Результаты поиска

Содержание photosmart 850

Отзывы:

Похожие инструкции для photosmart 850

Бренды по названию

Популярные бренды