HP photosmart 850 страница 28 Скачать руководство пользователя

Страница: 28 / 136

Loopback and null interface configuration
commands

default

Use

default

to restore the default settings for the loopback or null interface.

Syntax

default

Views

Loopback interface view, null interface view

Default command level

2: System level

Usage guidelines

CAUTION:

The

default

command might interrupt ongoing network services. Make sure you are fully aware of the

impacts of this command when you use it in a live network.

This command might fail to restore the default settings for some commands for reasons such as command

dependencies and system restrictions. Use the

display this

command in interface view to identify these

commands, and then use their

undo

forms or follow the command reference to individually restore their

default settings. If your restoration attempt still fails, follow the error message instructions to resolve the

problem.

Examples

# Restore the default settings of interface loopback 0.

<Sysname> system-view

[Sysname] interface loopback 0

[Sysname-loopback0] default

This command will restore the default settings. Continue? [Y/N]:y

description

Use

description

to change the text description for the current interface.

Use

undo description

to restore the default description.

Syntax

description

text

undo

description

Содержание photosmart 850









































































































































Результаты поиска

Содержание photosmart 850

Отзывы:

Похожие инструкции для photosmart 850

Бренды по названию

Популярные бренды

HP photosmart 850, Справочник по командам

Результаты поиска

Содержание photosmart 850

Отзывы:

Похожие инструкции для photosmart 850

Бренды по названию

Популярные бренды