HP photosmart 850 Скачать руководство пользователя страница 19

Страница: 19 / 136

[Sysname-port-group-manual-group1] group-member Ten-gigabitethernet 1/0/1 to Ten-Gig

abitEthernet 1/0/2

[Sysname-port-group-manual-group1] jumboframe enable

# Enable jumbo frames to pass through Ten-GigabitEthernet 1/0/1.

<Sysname> system-view

[Sysname] interface ten-gigabitethernet 1/0/1

[Sysname-Ten-GigabitEthernet1/0/1] jumboframe enable

loopback internal

Use

loopback internal

to perform a loopback test on an Ethernet interface.

Use

undo loopback

to cancel a loopback test on an Ethernet interface.

Syntax

loopback internal

undo loopback

Default

Loopback test is not performed on an Ethernet interface.

Views

Ethernet interface view

Default command level

2: System level

Parameters

internal

: Performs an internal loopback test on the Ethernet interface.

Usage guidelines

Enable internal loopback testing for troubleshooting purposes, such as identifying an Ethernet problem.
During a loopback test, the Ethernet interface operates in full duplex mode. When the loopback test is

complete, the interface returns to its duplex setting.

Examples

# Perform an internal loopback test on interface Ten-GigabitEthernet 1/0/1.

<Sysname> system-view

[Sysname] interface Ten-GigabitEthernet 1/0/1

[Sysname-Ten-GigabitEthernet1/0/1] loopback internal

reset counters interface

Use

reset counters interface

to clear the Ethernet interface statistics.

Syntax

reset counters interface

[

interface-type

[

interface-number

]

Views

User view

Содержание photosmart 850









































































































































Результаты поиска

Содержание photosmart 850

Отзывы:

Бренды по названию

Популярные бренды

HP photosmart 850, Справочник по командам

Результаты поиска

Содержание photosmart 850

Отзывы:

Бренды по названию

Популярные бренды