manualshive.com logo in svg

HP photosmart 850, Справочник по командам

Поделиться
Скачать
HP photosmart 850 Скачать руководство пользователя страница 17

12 

Parameters 

auto

: Sets the interface to operate in autonegotiation mode.  

full

: Sets the interface to operate in full duplex mode.  

Usage guidelines 

Support for this command varies with device models. For more information, see 

About the Command 

References for HP Unified Wired-WLAN Products

.  

Examples 

# Configure interface Ten-GigabitEthernet 1/0/1 to operate in autonegotiation mode. 

<Sysname> system-view 

[Sysname] interface ten-gigabitethernet 1/0/1 

[Sysname-Ten-GigabitEthernet1/0/1] duplex auto 

flow-interval 

Use 

flow-interval 

to set the interface statistics polling interval. 

Use 

undo flow-interval 

to restore the default interval. 

Syntax 

flow-interval 

interval 

undo flow-interval 

Default 

The interface statistics polling interval is 300 seconds. 

Views 

Layer 2 Ethernet interface view 

Default command level 

2: System level 

Parameters 

interval

: Sets the statistics polling interval, in seconds. It is in the range of 5 to 300 and must be a multiple 

of 5. 

Examples 

# Set the statistics polling interval to 100 seconds on Ten-GigabitEthernet 1/0/1.  

<Sysname> system-view 

[Sysname] interface ten-gigabitethernet 1/0/1 

[Sysname-Ten-GigabitEthernet1/0/1] flow-interval 100 

interface 

Use 

interface 

to enter interface view.  

Syntax 

interface 

interface-type

  

interface-number

 

Содержание photosmart 850









































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды