HP photosmart 850 страница 125 Скачать руководство пользователя | Manualshive

Страница: 125 / 136

background image

120

Default

The TTL multiplier is 4.

Views

System view

Default command level

2: System level

Parameters

value

: Sets the TTL multiplier, ranging from 2 to 10.

Usage guidelines

You can set the TTL of the local device information by configuring the TTL multiplier.
The TTL configuration of a device is determined by the expression:
TTL multiplier × LLDP frame transmission interval
The TTL can be up to 65535 seconds. Longer TTLs will be rounded off to 65535 seconds.

Examples

# Set the TTL multiplier to 6.

<Sysname> system-view

[Sysname] lldp hold-multiplier 6

Related commands

lldp timer tx-interval

lldp management-address-format string

Use

lldp management-address-format string

to encapsulate the management address in the form of

strings in TLVs.
Use

undo lldp management-address-format

to restore the default.

Syntax

lldp management-address-format string
undo lldp management-address-format

Default

The management address is encapsulated in the form of numbers in TLVs.

Views

Layer 2 Ethernet interface view, port group view

Default command level

2: System level

Examples

# Configure Ten-GigabitEthernet 1/0/1 to encapsulate the management address in the form of strings

in management address TLVs.

<Sysname> system-view

[Sysname] interface ten-gigabitethernet1/0/1

«
...
123
124
125
126
127
...
»

Содержание photosmart 850









































































































































Отзывы:

Нет отзывов

Похожие инструкции для photosmart 850

Бренд: GE Страницы: 76

Бренд: YESKAMO Страницы: 28

Бренд: CamPro Страницы: 14

Бренд: Federal Signal Corporation Страницы: 20

SP-560 UZ - Compact

Бренд: Olympus Страницы: 3

SP-560 UZ - Compact

Бренд: Olympus Страницы: 96

Бренд: Olympus Страницы: 96

Бренд: Olympus Страницы: 84

SP 570 - UZ Digital Camera

Бренд: Olympus Страницы: 4

Бренд: Olympus Страницы: 191

SP 700 - 6 Megapixel Digital Camera

Бренд: Olympus Страницы: 187

SP 320 - Digital Camera - 7.1 Megapixel

Бренд: Olympus Страницы: 191

Бренд: Olympus Страницы: 109

KIT-V00137 - Stylus 1040 Digital Camera

Бренд: Olympus Страницы: 69

IR 500 - 4MP Digital Solutions Camera

Бренд: Olympus Страницы: 259

IR 500 - 4MP Digital Solutions Camera

Бренд: Olympus Страницы: 259

IR 300 - Digital Camera - 5.0 Megapixel

Бренд: Olympus Страницы: 182

IR 300 - Digital Camera - 5.0 Megapixel

Бренд: Olympus Страницы: 182

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды