HP photosmart 850 Скачать руководство пользователя

Страница: 124 / 136

119

Default command level

2: System level

Usage guidelines

The command does not apply to LLDP-CDP packets, which use only SNAP encapsulation.

Examples

# Configure the encapsulation format for LLDP frames as SNAP on Ten-GigabitEthernet 1/0/1.

<Sysname> system-view

[Sysname] interface ten-gigabitethernet1/0/1

[Sysname-Ten-GigabitEthernet1/0/1] lldp encapsulation snap

lldp fast-count

Use

lldp fast-count

to set the number of the LLDP frames sent each time fast LLDP frame transmission is

triggered.
Use

undo lldp fast-count

to restore the default.

Syntax

lldp fast-count

count

undo lldp fast-count

Default

The number is 3.

Views

System view

Default command level

2: System level

Parameters

count

: Sets the number of the LLDP frames sent each time fast LLDP frame transmission is triggered. The

argument ranges from 1 to 10.

Examples

# Configure the device to send four LLDP frames each time fast LLDP frame transmission is triggered.

<Sysname> system-view

[Sysname] lldp fast-count 4

lldp hold-multiplier

Use

lldp hold-multiplier

to set the TTL multiplier.

Use

undo lldp hold-multiplier to

restore the default.

Syntax

lldp hold-multiplier

value

undo lldp hold-multiplier

Содержание photosmart 850









































































































































Результаты поиска

Содержание photosmart 850

Отзывы:

Похожие инструкции для photosmart 850

Бренды по названию

Популярные бренды

HP photosmart 850, Справочник по командам

Результаты поиска

Содержание photosmart 850

Отзывы:

Похожие инструкции для photosmart 850

Бренды по названию

Популярные бренды