HP Performance Optimized Datacenter 20c Скачать руководство пользователя

Страница: 46 / 88

Removal and replacement procedures 46

Remove the sensor from the water piping.

Replacing the chilled water supply and return header pressure sensor

Position the sensor as it was before removal.

Connect the sensor to the sensing tube.

Using a wrench, rotate the sensor retaining nut clockwise to tighten it.

Reconnect the sensor wiring.

Chilled water flow sensor

Removing the chilled water flow sensor

Label the wired connections or take a picture to remember which wires to reconnect to the chilled water
flow sensor.

Содержание Performance Optimized Datacenter 20c

























































































Результаты поиска

Содержание Performance Optimized Datacenter 20c

Отзывы:

Похожие инструкции для Performance Optimized Datacenter 20c

Бренды по названию

Популярные бренды

HP Performance Optimized Datacenter 20c, Руководство по техническому обслуживанию и ремонту

Результаты поиска

Содержание Performance Optimized Datacenter 20c

Отзывы:

Похожие инструкции для Performance Optimized Datacenter 20c

Бренды по названию

Популярные бренды