HP Performance Optimized Datacenter 20c Скачать руководство пользователя

Страница: 36 / 88

Removal and replacement procedures 36

Pull the filter down through the frame channels to remove it.

Replacing the heat exchanger air filter

Angle the filter to position the top corners in the frame channels, and then push the filter up to the top of
the frame.

Push in the bottom corners of the filter until the locking tabs engage and the filter clicks into place.

VESDA filter

The VESDA filter sensor notifies you through the ECS when a filter must be changed. HP recommends

periodically inspecting and changing each VESDA filter. A VESDA filter can be replaced during normal HP

POD 20c operation.
You need a Phillips-head screwdriver for installation.

Содержание Performance Optimized Datacenter 20c

























































































Результаты поиска

Содержание Performance Optimized Datacenter 20c

Отзывы:

Похожие инструкции для Performance Optimized Datacenter 20c

Бренды по названию

Популярные бренды

HP Performance Optimized Datacenter 20c, Руководство по техническому обслуживанию и ремонту

Результаты поиска

Содержание Performance Optimized Datacenter 20c

Отзывы:

Похожие инструкции для Performance Optimized Datacenter 20c

Бренды по названию

Популярные бренды